BPM Heating, Cooling & Plumbing holds Maryland HVAC Master license #75803 and Master Plumber/Gas Fitter license #86156, covering the full scope of hydronic radiant system design and installation under one roof. The team brings over 100 years of combined experience across heating systems, including boiler-based hydronic work in Frederick’s older and newer housing stock alike. BPM is a Lennox Premier Dealer and Trane Authorized Dealer, with certified expertise in high-efficiency heat sources that pair with radiant distribution. Financing is available through Nymeo Federal Credit Union for homeowners planning a larger radiant project.
Get in touch with us to schedule service or request a free quote on any new installation.
However we end up at your door, the experience runs the same way. Every BPM visit means licensed HVAC and plumbing professionals, clear communication, honest pricing, and technicians who respect your home and your time. Here’s what to expect, start to finish.
Tell us what's going on, and we'll get you on the schedule at a time that works for your day.
You'll get a confirmation and an "on the way" notification before your technician arrives — so you're never left guessing or waiting around.
Your technician walks you through what they're going to do and what it costs before any work begins — in plain language, with no pressure.
We complete the job, clean up after ourselves, and make sure everything's running right before we leave.
You have probably been living with the problem long enough that it has a name in your house. The basement that stays cold no matter what the thermostat says. The addition that never gets warm because the duct run is too long. The main floor that cycles between too hot near the vents and too cold everywhere else. Or maybe you are tearing out the old system anyway during a renovation and you finally have the chance to do this right.
The appeal of radiant heat is not hard to understand. A floor that is warm underfoot in January. No forced air moving dust around. No registers to work around when you are laying out furniture. Heat that rises evenly from the surface rather than blasting from a vent and stratifying near the ceiling. If you have been in a home with a well-done radiant system, you know the difference is real.
What you are probably less sure about is whether your specific home — your existing boiler or lack of one, your floor construction, your budget, your renovation timeline — actually makes radiant the right call. That uncertainty is exactly right. Radiant is not the correct answer for every situation, and the research you have done probably surfaced enough conflicting information to make you want a straight conversation with someone who installs these systems in real Frederick homes.
Some of what you may be weighing:
Those are the right questions. They deserve honest answers, not a sales pitch.
We recently purchased a historic 1895 home in downtown Frederick and the giant steam boiler stopped working just a month after moving in. Scrambling to try to figure out what to do, I solicited several quotes, realizing quickly that simply replacing the boiler, may not be the best option for the house. Rich from BMP was excellent from the very first meeting, he was super professional and knowledgeable and gave me various options by thinking “outside the box” of what was possible. The solution he presented was perfect, it eliminated the steam boiler, while providing a dual system that was much more energy efficient, and included no mounted mini-splits on the first floor! This was a critical piece, in keeping the historic look of the home.
Angela W. · May 2024 Read on Yelp →
I can say nothing but positive things about this company. We lost our furnace last year and had a ducted mini split system installed with a different company and had absolutely nothing but problems – the employees disgradering our concerns and never called back in a timley manner – just a nightmare for the past year. Rich was very comprehensive and came out to our home multiple times while we had the previous system removed and made suggestions to heat and cool our old house properly. He answered all my questions, kept me informed with updates, and they were able to have our new gas furnace installed with barely any wait. We live in a 1900s house that is now able to stay chilly at 66°F on a 100°F day, I never thought that would be possible; they really thought of everything and made the best recommendations for the condition of our old house.
Kalynn Murray · August 2023 Read on Google →
Certifications & Licensing
Manufacturer dealer status and state licenses aren't decorations — they affect which warranty terms you get on new equipment, who's allowed to pull your permits, and whose installation work the manufacturer will stand behind.
Lennox
Premier Dealer
Trane
Authorized Dealer
LG
Pro Platinum Dealer
Samsung
Powered by Specialist
Maryland HVAC Master License #75803 · Master Plumber / Gas Fitter #86156
Manufacturer dealer certifications require demonstrated installation quality, verified customer satisfaction ratings, and completed factory training. Premier and Authorized status also unlocks enhanced warranty options on new equipment — terms that aren't available through uncertified installers. The LG Pro Platinum designation is LG's highest contractor tier, covering cold-climate and inverter-driven systems specifically.
The first conversation is about your home, not a product. Before anything is quoted or specified, BPM looks at what you actually have: the heat source situation, the floor construction, the zones you want to cover, and how the project fits into whatever else is happening — a renovation, a new addition, a standalone basement project. Radiant is not a one-size system, and the design that makes sense for a slab-on-grade basement is different from what works under hardwood in a second-floor addition.
BPM holds both HVAC and plumbing licenses, which matters for hydronic radiant work. The boiler, the tubing, the manifolds, the controls — that is all one project with one contractor, not a coordination problem between two trades. If your existing boiler is a viable heat source for a radiant loop, you will hear that honestly. If it is not — because the output temperature is wrong for a low-temperature radiant system, or because the capacity is not there — that comes up in the assessment, not after the tubing is already in the floor.
What the installation process actually looks like depends on your floor construction and scope. For a new addition or a slab pour, tubing goes in before the concrete — minimal disruption to the rest of the house. For a retrofit over an existing subfloor, the approach depends on floor height constraints and what is going above. BPM explains the options and the tradeoffs before anything is opened up, so you are making the decision with full information about what the project involves.
Controls for radiant systems can be straightforward or genuinely complicated depending on how many zones you have and what the rest of the house is doing. If you are adding radiant to one zone in a house that still has forced air elsewhere, the controls need to be set up so both systems work together without fighting each other. BPM handles that integration — you get a walkthrough of how the system operates before the crew leaves.
When the work is done, you know what was installed, why it was configured the way it was, and what to expect from the system over time. Radiant systems are low-maintenance by nature, but there are things worth knowing — like how to identify a pressure drop in a hydronic loop before it becomes a problem, and what a normal radiant heating maintenance interval looks like. That conversation happens at the end of every installation.
Get in touch with us to schedule service or request a free quote on any new installation.
Hello Everyone!!
We have had an issue with Blower motor in our HVAC. We contacted 9 HVAC companies and they are all advised to replace the entire system but Mr.Rich from BPM is very kind to ask about the actual problem and provided 3 different options one of them is to replace the actual issue instead of replacing the full system.
Also, Mr.Rich informed us that, the current system is in good condition and will work for another couple of years based on his expertise in this field.
The technician Mr.Mychall is very professional and he fixed the actual problem in less than an hour.
This company helped to save thousands of dollars in HVAC expenses for us.
I would happily and strongly recommend BPM HVAC service to everyone who is need of the HVAC and their Plumbing repairs as well.
Baulraj Vanamamalai · May 2025 Read on Google →
BEST experience!!! BPM Heating & Cooling was my 4th quote for a new furnace and a/c unit. They explained everything completely, did not give any run around on my questions, provided a reasonable quote and reasonable finance options, if needed. Further, they went above and beyond to make sure the home was comfortable until the install date. All BPM staff were informative and polite at every step. I highly recommend BPM Heating & Cooling!!
SL-S · June 2025 Read on Google →
BPM installed our second commercial HVAC system and just like the previous one for a different unit, the process was smooth and efficient. We strongly recommend Bert and his team.
Stephan Beauchesne · December 2025 Read on Google →
Radiant works best when it is designed into the project from the start — a new addition, a slab pour, or a renovation where the floor is already coming up. Retrofitting radiant into a finished space with existing flooring is possible but adds cost and complexity, and in some cases the floor height constraints make it impractical without significant modification. The honest answer is that radiant is a strong fit for some Frederick homes and a poor fit for others, and the only way to know which category yours falls into is to look at the actual floor construction, the heat source situation, and the scope of work you are already doing. BPM will tell you directly if the project does not pencil out for your situation.
Hydronic radiant circulates warm water through tubing embedded in or under the floor — it requires a boiler or water heater as a heat source and is the better choice for whole-house or large-zone applications because the operating cost over time is significantly lower than electric. Electric radiant uses resistance mats or cables and is simpler to install, but the ongoing electricity cost makes it impractical as a primary heat source for large areas — it works well for a single bathroom floor or a small supplemental zone where the installation cost of a hydronic system would not be justified. For most Frederick homeowners looking at radiant as a meaningful part of their heating system, hydronic is the right direction.
It depends on what you have. Radiant systems typically run at lower water temperatures than traditional baseboard or radiator systems — around 90–120°F rather than 140–180°F — which means some older high-temperature boilers are not a good match without modifications. If you have a modern condensing boiler or a heat pump water heater, compatibility is more likely. BPM evaluates your existing equipment as part of the project assessment and tells you whether it can serve the radiant loop, whether it needs to be modified, or whether a new heat source is the right call. That determination happens before anything is quoted, not after. If a new boiler is needed, boiler installation is handled by the same team under the same project.
For new construction, additions, or projects where the slab has not been poured yet, installation is minimally disruptive to the rest of the house — the tubing goes in before the concrete or subfloor, and the living space is not affected. Retrofitting into an existing finished floor is a different story: depending on the approach, it may involve removing and replacing flooring, or it may be possible to run low-profile tubing systems under the subfloor from below if there is accessible basement or crawl space. The scope and disruption level varies significantly by project, and BPM walks through what your specific floor construction requires before any work starts.
Hydronic radiant installation costs vary widely based on the scope — a single-zone basement slab project is a fundamentally different job than a whole-house retrofit with a new boiler. As a rough frame: electric radiant for a single bathroom typically runs a few hundred to low thousands of dollars installed. Hydronic radiant for a single zone in a new addition or unfinished basement runs from several thousand dollars upward depending on square footage and whether the heat source is already in place. Whole-house hydronic systems with a new boiler are larger investments — often $15,000–$30,000 or more depending on the home. The variables that move the number most are floor construction, zone count, heat source requirements, and whether the project is new construction or a retrofit. BPM provides a project-specific quote after seeing the actual conditions.
Yes, in the right circumstances. A single-zone hydronic radiant project makes the most sense when it is part of a larger construction or renovation project — a new basement slab, an addition, a bathroom remodel where the floor is already coming up. Standalone single-room hydronic retrofits in finished spaces can be harder to justify on cost alone. Electric radiant for a single bathroom or small supplemental zone is often the more practical answer when the project is limited in scope. The question is really whether the installation cost is proportionate to what you are getting — and that depends on how the project is structured, not just the square footage.
Hydronic radiant systems are generally more efficient than forced-air heating because they operate at lower temperatures and deliver heat more evenly, which means the thermostat does not need to be set as high to achieve the same comfort level. There is no duct heat loss, which can account for 20–30% of energy waste in a typical forced-air system. The actual savings depend on the heat source — a high-efficiency condensing boiler or a heat pump paired with radiant will outperform an older forced-air system significantly. Electric radiant is less efficient than hydronic for large areas due to electricity rates, which is why it is best reserved for small supplemental zones. Maryland homeowners may also qualify for HVAC rebates and incentives that can offset the upfront cost of a high-efficiency system.
